How would you go about laying your bike down?

unknownroad · 11-10-2009, 11:32 AM

I'd take a couple of shop towels, fold one up a few times and put it over the bar end, and just fold the other one in half to go under the tank. Stand on the down side, grip the bar on the down side with one hand, and the grab rail or underseat rail with the other. Start close to the bike and walk backwards slowly, bending at the knees as it gets closer to the ground. If you've got the leg strength, it'll be smoother if you balance the bike on one knee as it gets lower, and switch your grip to the up-side bar end.

Getting it upside-down, I usually grab the fork with one hand and the back wheel with the other, and turn the wheel sideways once the bike is high enough off the ground. That way, the handlebars are in line with the bike rather than moving your pivot point way out to the side. Best to have a few extra towels, and work on a rubber mat.

askmrjesus · 11-10-2009, 11:34 AM

Quote:

Originally Posted by unknownroad

I'd take a couple of shop towels, fold one up a few times and put it over the bar end, and just fold the other one in half to go under the tank. Stand on the down side, grip the bar on the down side with one hand, and the grab rail or underseat rail with the other. Start close to the bike and walk backwards slowly, bending at the knees as it gets closer to the ground. If you've got the leg strength, it'll be smoother if you balance the bike on one knee as it gets lower, and switch your grip to the up-side bar end.

Getting it upside-down, I usually grab the fork with one hand and the back wheel with the other, and turn the wheel sideways once the bike is high enough off the ground. That way, the handlebars are in line with the bike rather than moving your pivot point way out to the side. Best to have a few extra towels, and work on a rubber mat.

Or, you could just let Tigger ride it.

JC

azoomm · 11-10-2009, 11:40 AM

I do it only to make epic slides underneath semi trailers....

Rider · 11-10-2009, 12:05 PM

Quote:

Originally Posted by azoomm

I do it only to make epic slides underneath semi trailers....

I tried that but I ended up under the wheels.

z06boy · 11-10-2009, 12:06 PM

I learned everything I need to know right here...

11-10-2009, 11:32 AM	#1
unknownroad Guys... where are we? Join Date: Nov 2008 Location: South Carolina Moto: SV650 Interstate, CX500 rat-bobber, whatever else runs. Posts: 784	I'd take a couple of shop towels, fold one up a few times and put it over the bar end, and just fold the other one in half to go under the tank. Stand on the down side, grip the bar on the down side with one hand, and the grab rail or underseat rail with the other. Start close to the bike and walk backwards slowly, bending at the knees as it gets closer to the ground. If you've got the leg strength, it'll be smoother if you balance the bike on one knee as it gets lower, and switch your grip to the up-side bar end. Getting it upside-down, I usually grab the fork with one hand and the back wheel with the other, and turn the wheel sideways once the bike is high enough off the ground. That way, the handlebars are in line with the bike rather than moving your pivot point way out to the side. Best to have a few extra towels, and work on a rubber mat. __________________ Considering Verizon Business service? Perhaps you'd like to consider a nice drain cleaner enema instead?

11-10-2009, 11:40 AM	#3
azoomm moderator chick Join Date: Feb 2008 Location: Hill Country TX Moto: Pasta Rockets Posts: 8,917	I do it only to make epic slides underneath semi trailers.... __________________ We have enough youth. How about a fountain of "smart"? Come Play at the Track!! http://www.elitetrackdays.com

11-10-2009, 12:06 PM	#5
z06boy Letzroll Join Date: Feb 2008 Location: Lake Norman area, NC Moto: 07 Red R1 & 07 Blue R6 Posts: 5,265	I learned everything I need to know right here... Last edited by z06boy; 11-10-2009 at 12:23 PM..