Go Back   Two Wheel Fix > In the Garage or Shop > Mechanical or Tech

Reply
 
Thread Tools Display Modes
Old 05-12-2012, 11:45 PM   #1
Cutty72
Ride Naked.
 
Cutty72's Avatar
 
Join Date: Feb 2008
Location: Flat and Straight ND
Moto: 08 BUELL 1125R, 05 SV650S
Posts: 7,916
Default 1125 Valve check

Ok, here it is finally.
I realize going through the pictures, that I did ok with them on the dis-assembly, but sucked ass while reassembling. Guess you will just have to remember how I/you took it apart!

Start with a complete 1125R





Add in a couple helpers



And let the project begin.

Start by removing all the plastics. If you can't do this on your own, just take it to the dealer...





Left side, closer



Right side, closer



I took pics of how all the wiring was run, so I could be sure to put it back the same. It's pretty simple, all the wires have different connectors so it is virtually impossible to hook something back up incorrectly.





__________________
Adrenaline... the wonder drug.

Quote:
Originally Posted by Gas Man View Post
Again... Cutty you are one smart man!!
Quote:
Originally Posted by The Chi View Post
If I have to get help to get it back up, I dont need to be riding it.

3662 Supply NCO

Cutty72 is offline   Reply With Quote
Old 05-12-2012, 11:50 PM   #2
derf
token jewboy
 
derf's Avatar
 
Join Date: Nov 2008
Moto: CBR 900, KLR ugly ass duckling, Gas Man
Posts: 10,799
Default

looks like it sucks
__________________
derf is offline   Reply With Quote
Old 05-13-2012, 12:01 AM   #3
Cutty72
Ride Naked.
 
Cutty72's Avatar
 
Join Date: Feb 2008
Location: Flat and Straight ND
Moto: 08 BUELL 1125R, 05 SV650S
Posts: 7,916
Default

Next, start the bike, disconnect the fuel pump while running to drain the fuel rail. After it dies, crank it again for a couple seconds to be sure.



After you are done cranking the bike, put rags in the intake to prevent anything from being dropped in them.
Then, disconnect the fuel rail, be sure to plug/cap the lines so no shit gets in them.



Disconnect the throttle cables.



Disconnect all the other wiring. Horn wires, O2 sensors, speed sensor, main ECM cable, clutch cable, rear brake line...

By this point, my assistants were getting rather bored...



Next, remove the muffler and set aside. Then position a floor jack under the engine to support it.



Also at this time, position whatever it is you are going to support the front end/frame with.

Then, remove the 7 bolts connecting the frame/tank to the engine (yes, just 7) 1. Shock to swingarm 2 & 3 front K brackets to front of engine (radiators must be loose to get to them) 4 & 5 Rear area of frame/tank 6 & 7 Further up, on the right side there is a pinch bolt that must be loosened first.
Once all the bolts are removed, start lifting the frame SLOWLY to ensure that all the wiring has been disconnected properly.
__________________
Adrenaline... the wonder drug.

Quote:
Originally Posted by Gas Man View Post
Again... Cutty you are one smart man!!
Quote:
Originally Posted by The Chi View Post
If I have to get help to get it back up, I dont need to be riding it.

3662 Supply NCO


Last edited by Cutty72; 05-13-2012 at 12:43 AM..
Cutty72 is offline   Reply With Quote
Old 05-13-2012, 12:27 AM   #4
Cutty72
Ride Naked.
 
Cutty72's Avatar
 
Join Date: Feb 2008
Location: Flat and Straight ND
Moto: 08 BUELL 1125R, 05 SV650S
Posts: 7,916
Default

VIOLA, you now have 2 half bikes!





While I had it apart, I applied heat tape to the inside of the frame/tank. Not sure if it will help, but it can't hurt anything.





Remove the stator puck and plug, this is how you will rotate the engine.



Then, remove the heads and start the valve check/adjustment per the manual.



Loosen the plugs, but leave them in place as this will prevent you from accidentally dropping anything into the engine.
I had good luck using a magnet tool to remove and replace the shims. Wipe them off with a rag first to remove the oil "seal" that holds them in place and they come right out. Measure with a micrometer or a caliper to get proper size of the old, and replace with the new using the formula in manual.
All of mine were on the edge of in spec tight, or out of spec tight.
Now they are all in spec mid to loose.
__________________
Adrenaline... the wonder drug.

Quote:
Originally Posted by Gas Man View Post
Again... Cutty you are one smart man!!
Quote:
Originally Posted by The Chi View Post
If I have to get help to get it back up, I dont need to be riding it.

3662 Supply NCO

Cutty72 is offline   Reply With Quote
Old 05-13-2012, 12:34 AM   #5
Cutty72
Ride Naked.
 
Cutty72's Avatar
 
Join Date: Feb 2008
Location: Flat and Straight ND
Moto: 08 BUELL 1125R, 05 SV650S
Posts: 7,916
Default

And here are the tools I used to complete the job.



Feeler gauge
spark plug wrench/socket
Caliper
Rubber mallet
small flat tip screwdriver
large flat tip screwdriver
T30 driver
T40 driver
4mm allen
5mm allen
6mm allen
8mm allen
4mm allen L shape
snap ring pliers
side cutter
8mm wrench
10mm wrench
13mm wrench
14mm wrench
magnet tool
needle nose pliers
channel lock pliers
ratchet w/ extension
8mm socket
17mm socket
mity vac (or your favorite way to bleed brakes/clutch)
turkey baster
Dot 4 brake fluid
Shim kit (10mm o.d.)
Coolant (optional)
rags
Oil and filter

And the most important



The manual.
__________________
Adrenaline... the wonder drug.

Quote:
Originally Posted by Gas Man View Post
Again... Cutty you are one smart man!!
Quote:
Originally Posted by The Chi View Post
If I have to get help to get it back up, I dont need to be riding it.

3662 Supply NCO

Cutty72 is offline   Reply With Quote
Old 05-13-2012, 12:40 AM   #6
Cutty72
Ride Naked.
 
Cutty72's Avatar
 
Join Date: Feb 2008
Location: Flat and Straight ND
Moto: 08 BUELL 1125R, 05 SV650S
Posts: 7,916
Default

Putting it back together is just a reverse of the disassembly.
It actually went back together very easily. All the wires are quick connect so they can't be hooked up incorrectly, so as long as you don't miss a connection, you should be good to go.

Before I put all the plastics back on I also did a coolant flush with Engine Ice, flushed both brakes and clutch, and a complete oil change, to include pulling the sump plate since the exhaust was off anyway. Didn't need to, as it was clean, but now I know!

Sorry for not having any reassembly pics, I ended up doing that a little at a time while I had time in the evenings. I hate doing it that way for fear I may miss something, but I had no extra parts, and everything seems to run smoothly.

If you have any questions about the procedure, feel free to ask. It was not nearly as difficult as I expected, mostly just time consuming.
__________________
Adrenaline... the wonder drug.

Quote:
Originally Posted by Gas Man View Post
Again... Cutty you are one smart man!!
Quote:
Originally Posted by The Chi View Post
If I have to get help to get it back up, I dont need to be riding it.

3662 Supply NCO

Cutty72 is offline   Reply With Quote
Old 05-13-2012, 12:45 AM   #7
Cutty72
Ride Naked.
 
Cutty72's Avatar
 
Join Date: Feb 2008
Location: Flat and Straight ND
Moto: 08 BUELL 1125R, 05 SV650S
Posts: 7,916
Default

Quote:
Originally Posted by derf View Post
looks like it sucks
Not nearly as bad as I thought going in. And WAY easier than writing a $1000+ check to the dealer to do it! (probably wrong/half assed anyway)
__________________
Adrenaline... the wonder drug.

Quote:
Originally Posted by Gas Man View Post
Again... Cutty you are one smart man!!
Quote:
Originally Posted by The Chi View Post
If I have to get help to get it back up, I dont need to be riding it.

3662 Supply NCO

Cutty72 is offline   Reply With Quote
Old 05-13-2012, 07:10 AM   #8
tommymac
Moto GP Star
 
tommymac's Avatar
 
Join Date: Nov 2008
Posts: 11,022
Default

Good stuff, I am sure my 5 little helpers would sleep through the entire project and just bug me to feed them

Thats nice you can keep the front end all together, that will def save me soem time. Just wondering if I should do the bearrings then, if I need to, or make that another project. Theres a fair amt of room up front so i think I can do them without taking the body work off.
tommymac is offline   Reply With Quote
Old 05-13-2012, 08:17 PM   #9
Cutty72
Ride Naked.
 
Cutty72's Avatar
 
Join Date: Feb 2008
Location: Flat and Straight ND
Moto: 08 BUELL 1125R, 05 SV650S
Posts: 7,916
Default

Quote:
Originally Posted by tommymac View Post
Good stuff, I am sure my 5 little helpers would sleep through the entire project and just bug me to feed them

Thats nice you can keep the front end all together, that will def save me soem time. Just wondering if I should do the bearrings then, if I need to, or make that another project. Theres a fair amt of room up front so i think I can do them without taking the body work off.
You realize that it is only 4 nuts (the mirrors) and 2 bolts to remove the front fairing right?

If you split it like I did, it would probably be easier to do the bearings after it's back together. At least frame connected to engine.
__________________
Adrenaline... the wonder drug.

Quote:
Originally Posted by Gas Man View Post
Again... Cutty you are one smart man!!
Quote:
Originally Posted by The Chi View Post
If I have to get help to get it back up, I dont need to be riding it.

3662 Supply NCO

Cutty72 is offline   Reply With Quote
Old 05-13-2012, 11:11 PM   #10
No Worries
Keyboard Racer
 
No Worries's Avatar
 
Join Date: Feb 2008
Location: Mile High City
Moto: Old Superbikes
Posts: 1,016
Default

I'm impressed.
No Worries is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:33 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.